 |
CircuitWerkes Support (PDF manuals and software)
Manuals have a funny way of
walking away just when you need 'em, so this way
you always have our information available to
you. The books are in Adobe Acrobat 3.0 PDF
format. If your version of the reader is 2.xx or
older, it will not work, so you'll need to
download a free copy of the latest Acrobat
reader (ver. 7) or you can click here to
install it on your Windows 2000 or XP computer.
For older Windows systems, Acrobat 5 may be
installed.
This page contains links to
current production product
manuals and software. If you have an older
CircuitWerkes product, you can find out-of-production
items here .
The following products are
in current production:
- CP-2 - stand alone call
progress decoder for disconnecting any device
auto-answer device or 1A2 key set from a phone
line or PBX
- DR-10 - dial-up DTMF operated
remote control with audio hybrid and status
inputs. This book is for the latest version of
the DR-10 firmware, which is 1.3. For older
DR-10s, click here
. Manuals Updated 3-06-1999 for the DR-10a
or 8-06-97 for the original DR-10. A
simple DR-10 hookup diagram can be found on
our test tones
page.
- DS-8c - multi digit DTMF
sequence decoder
- DT-232 - DTMF
to Serial ASCII converter with telephone
autocouplerDTMF Tone Encoder
 DT-232 -
Windows GUI to control and configure DT-232.
CircuitWerkes
assumes no liability for bugs,
though
we would like to hear from you if you find
one. You must have
firmware version
7.00 or higher (released May, 2008) to use the
software.
If
you have version 5 or 6 firmware, please
contact us. If your version is
lower than 5, there is no software support,
but you can contact us about
an inexpensive upgrade for your DT-232 that
will bring it up to date.
If you get an "invalid setup package" or
"setup files corrupt" message when
installing the software, it means that your
web browser didn't completely
download the software. Try right clicking on
the link instead of left clciking
and then choose the "Save As" option.
Depending upon the web browser,
you might have to try the download a couple of
times. Be sure that the
downloaded file is 1.8 (or more) megabytes.
- DTMF-16d
-
Fully programmable DTMF tone
decoder with 16 outputs. Decodes
sequences and single tones with
multiple output modes. For the earlier DTMF-16C,
click here.
- EAS-4
- converts contact
closures into serial data for communicating
with the Sage ENDEC. Provides simplified
control for up to four stations equipped with
ENDEC and RP-2 option. A downloadable
Windows-based test program can be used on a
computer with a serial port to test your
EAS-4. Download the program installer from our
test tones page.
- GENr8
- DTMF Tone Encoder
GENr8r ver 1.3.12
- indows GUI to control and configure GENr8.
Version
1.3.12 is for use with version 5.0 firmware.
Replaced version 1.3.9.
Older version 1.3.9 is for use with version 4.0 firmware.
Replaced version 1.3.7
which shipped with
some recent units but had a
problem uploading
config data.
(For version 1.0,
download the original
version here)
- HC-3
(formerly AC-3a) - hybrid
telephone autocoupler with balanced audio.
Updated 3-25-98
- HC-3
with ComboLok Option (formerly AC-3A with
ComboLok) - hybrid telephone autocoupler w/
password security. Updated 6-10-03
- MicTel - amplified
Mic/line to telephone interface. The MicTel
has recently been updated and two versions are
available. If your MicTel was made prior to
April of 2006, you probably have MicTelv4.0. If your MicTel was made in April
of 2006 or later, you probably have
MicTel v5.0. Version 4.0 MicTels have
7 jumpers while Version 5.0 MicTels have 13
jumpers. Use the Configuration Jumper Locator
page of the tech manual to determine if your
MicTel matches your documentation.
. .
- CircuitWerkes Net
Scanner- Windows GUI
to find CircuitWerkes Web enabled devices on
your network. Works only with devices shipped
after 9-1-09 (Silence Sentinal v1.0, WebGain
v1.0 and Sicon-8 v 1.4)
.
.
- pREX
- programmable relay
expander
Configuration
Manager - Windows GUI to control
and configure pREX.
Get the original version of the pREX manager here.
- REX
- relay expander /
multiplier
- SEN-6
- Subaudible 25, 35 &
combo 25/35 Hz tone encoder. Provides
filtered, balanced audio in and out.
- Silence Sentinal - Web enabled 2 channel
audio monitor with silence & overload
detection and six, user controlled, relay
outputs with automatic operation.
Silence
Sentinal -
Multi-Site Monitoring,
control and configuration -
manager software for the
Silence Sentinal.
Older WebSS
Software:(includes the technical
manuals, too).
WebSSMulti_1_3_15_Setup.exe
is for WebSS FW 1.7-Alpha
WebSSMulti_1_3_10_Setup.exe works with
firmware version 1.4 and older
- SiteSentry2 - Web enabled 2 channel
audio monitor with silence & overload
detection and six, user controlled, relay
outputs with automatic operation.
SiteSentry2 (version 1.14) - Multi-Site
Monitoring, control and
configuration manager software for the
SiteSentry2
- SUB-03f
- In 2003, the SUB-03
series was completely redesigned and is a
major improvement over all previous decoders.
Using high stability filters and
microprocessor based tone detection and
control, these units boast superior noise
immunity, faster response times, fewer
detection errors, and a broader detection
range than any other decoder. They are quick
to install and reliable in operation.
- TAC-5
- dial-up DTMF operated remote control with
audio hybrid and one status input. TheTAC-5 is
similar to the DR-10 in function, but with
fewer relays and at a lower cost. The TAC-5
also has some updated features not found on
the DR-10.
- Telco-6
- Multi-line
telephone ring detector with relay outputs
- TelTap
- Manual
telephone coupler and monitor
- Temperature
Sensor - External
temperature board for Sicon-8 and
SiteSentry2.
- Transcon-16
- Bi-directional
contact closure transporter
These manuals have generally
printed amazingly well on a variety of printers,
however, they are not absolutely guaranteed to
print faithfully on every type of printer. If the
printed output doesn't look like what you see on
your screen, try a different printer or printer
driver.
If you are looking for manuals
for discontinued Gentner products,
please click here.
Please
note that we do not sell or service Gentner
products. The few links here are provided as a
courtesy to former Gentner product users who are
seeking technical documents for their products.
Test
Tones, programs and hookup information -
for your convenience, you can download DTMF and
subaudible tones for testing various
CircuitWerkes products. Additional test tools
and diagrams can also be found here.
Contact Us
- if you don't
see a manual listed that you need, or you
discover any problems with any manuals, send
e-mail to our support staff and we'll take care
of it for you.
|
